The Saniflo SaniCUBIC 1 is a pre-assembled heavy-duty simplex grinder pump that meets the demanding needs of commercial and residential sewage applications. The stainless steel grinder system liquefies solids into small particles prior to being passed through the 1-1/2" discharge. It is designed to handle multiple waste fixtures for applications such as residential single—or group homes, commercial buildings, schools and many more.

This new Saniflo SaniCUBIC 1 system consists of a 1-HP motor housed inside a compact but highly durable plastic enclosure. The motor has a high-performance grinding system and a fast-rotating cutting blade to reduce solids in the waste water stream from toilets, tubs and showers, sinks, washing machines, dishwashers, etc.

The Saniflo SaniCUBIC 1 operation is as simple as the installation. The effluent enters the pump through one of four different inlets – one on either side of the unit at the bottom and two along the top. The inlets can accommodate 1-1/2" or 4" diameter pipes. As soon as the waste water level reaches the trigger point, the pumping system activates. The effluent is then pumped out through 1-1/2" diameter rigid pipe connected to the top of the pump. The maximum pumping distances of this heavy-duty simplex grinder pump are 36 Ft vertically and/or 328 Ft horizontally.

Warranty: 2-Year Full Manufacturer Warranty
Extended 4-Year Warranty with Product Registration (www.Saniflo.com/Register)

The inside of the Saniflo SaniCUBIC 1 comprises a couple of pressure switches and a circuit board assembly, which starts and stops the unit, and a powerful motor, which drives the stainless steel cutting blade and the pump. The motor is sealed for life in an oil-filled enclosure. A common spindle/shaft drives the impeller and the macerator blade. The moving parts, therefore, are kept to an absolute minimum. Water and organic waste matter that enter the enclosure are reduced to slurry and are picked up by the impeller mounted beneath the motor. 

The Saniflo SaniCUBIC 1 pump can handle up to 50 GPM. If the incoming rate exceeds the discharge rate, the pump automatically signals the "alarm" stage. This will activate the visual alarm mounted on the pump's control panel and the audible alarm from the wired control box (if connected).

This grinder pump can be retrofitted into an existing sewage ejector basin of at least 24" in diameter for a quick and easy pump exchange. As the Saniflo SaniCUBIC 1 is considered a "plug and play" device, no chains or floats are needed. 

Note that the effluent pipe leading into the Saniflo SaniCUBIC 1 pump has to be installed with the required ¼" per foot gravity flow. If the drain is connected to the bottom inlet, there must be a 10" height difference (from the pump to connecting fixture).

Wastewater from other sanitary fixtures is discharged into the Saniflo SaniCUBIC 1 via four 1½-inch or 4" inlets on either side of the housing and on the top of the enclosure. The internal discharge pipe comes equipped with a check valve that prevents backflow into the unit. Isolating valves (ball, gate valves) must be installed on waste inlets and on the discharge pipe to ensure that any service/maintenance may be carried out safely.

The SaniCUBIC 1 unit has been designed with a 1-1/2" vent connection on the top of the enclosure. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. Using mechanical vents, air admittance valves or similar devices is not permitted as these are considered one-way air vent systems. 

The SaniCUBIC 1 has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. 

This grinder pump is ordered as a single unit only. No other fixtures are included.